Advice needed: Precihole mainspring measurements

All posts related to air-guns (air-rifles, airsoft, air-pistols, air-guns etc.).
Post Reply
User avatar
estousandy
One of Us (Nirvana)
One of Us (Nirvana)
Posts: 399
Joined: Fri Oct 23, 2009 3:41 pm
Location: KL

Advice needed: Precihole mainspring measurements

Post by estousandy » Thu Jul 10, 2014 5:49 pm

Hi,

The NEW SPRING is what i got when i ordered a Precihole spring online. OLD SPRING is the one which was inside my IHP35.

Image

The measurements are different & i doubt the NEW spring's genuineness, considering its surface finish as shown below.

Image

So,

> Can someone confirm the measurements of an original Precihole mainspring compared to what's shown in the image?
> If genuine, will the NEW spring be compatible enough for the IHP35? This considering the length & OD are smaller in the new one.
> What effect does the reduced OD & total length of spring will bear on the final performance? Piston remains the same.
> Is the Precihole piston seal/adapter a direct fit for IHP35 or similar?

I'm not planning to machine a new spring guide as of now.
Measurements shown above might have a slight error margin.

Thanks! : )
with guns we are citizens, without we are subjects

For Advertising mail webmaster
bandukbhandar
Almost at nirvana
Almost at nirvana
Posts: 210
Joined: Sun Jun 24, 2007 5:03 pm
Location: Indore (MP)

Re: Advice needed: Precihole mainspring measurements

Post by bandukbhandar » Fri Jul 11, 2014 2:44 pm

Why go for Precihole Spring. IHP also provides spring as spares and available at their distributors. It also cost less than Precihole spring.

User avatar
snIPer
Veteran
Veteran
Posts: 1664
Joined: Wed May 23, 2007 12:06 pm

Re: Advice needed: Precihole mainspring measurements

Post by snIPer » Fri Jul 11, 2014 4:27 pm

I guess the next question will be - which is the better of the two - IHP or Precihole?
/S
On my Epitaph - Off to Happy Hunting Grounds.

User avatar
estousandy
One of Us (Nirvana)
One of Us (Nirvana)
Posts: 399
Joined: Fri Oct 23, 2009 3:41 pm
Location: KL

Re: Advice needed: Precihole mainspring measurements

Post by estousandy » Fri Jul 11, 2014 5:09 pm

Thanks to all, especially Briha. I got all the answers : ) This one is not a match. I might go for a Gsmith or import.

This new one was ordered for another cheap rifle for 300Rs & i just wanted to know IHP compatibility & whether what i got is a genuine Precihole spring or a knockoff. My nearest dealer is some 70kms away so can't really get a comparo in person.

Nop the next question is already asked.

> Is the Precihole piston seal/adapter a direct fit for IHP35 or similar?

This because i've access to only Precihole parts as of now, & that is directly from the factory.
with guns we are citizens, without we are subjects

User avatar
brihacharan
Old Timer
Old Timer
Posts: 3112
Joined: Fri Jan 22, 2010 3:33 pm
Location: mumbai

Re: Advice needed: Precihole mainspring measurements

Post by brihacharan » Fri Jul 11, 2014 5:19 pm

[quote="estousandy"]
Thanks to all, especially Briha. I got all the answers!
> Is the Precihole piston seal/adapter a direct fit for IHP35 or similar?

> No the adapter wont fit - The seal can.....
> Hence no point in trying to mix & match....
> The present IHP's synthetic seals are good - you may order from them direct....
Briha

User avatar
estousandy
One of Us (Nirvana)
One of Us (Nirvana)
Posts: 399
Joined: Fri Oct 23, 2009 3:41 pm
Location: KL

Re: Advice needed: Precihole mainspring measurements

Post by estousandy » Fri Jul 11, 2014 5:29 pm

All clear. Thanks again! : )

Sandip
with guns we are citizens, without we are subjects

Post Reply