Indians For Guns

Hi Everyone,

I have a very old air-rifle local kolkata make the name is Jimmy Mod-65 in .22 cal i had purchased it in 1996 the problem is that when ever i fire a pellet it get stuck into the barrel many times i had removed the pellets but now i am fed up pls any body can suggest what should i do with it.

Also it has rusted a bit as there was nobody to look after her so pls tell me can i make it as it was previous.

Also i had purchased a G-Smith Spring & washer for my IHP-35 I want to replace the main spring of my ihp to G-smith spring.

Actually my problem is i have holidays only on sundays & in mumbai all gunshops r closed on sunday & i cannot take off from my office.Mumbai Guys pls help me.

Also the shops r very far from my house it takes about 1hr for me from train to take C.S.T i live in Navi-Mumbai can anybody help me ready to pay the prize for my job

There is a gunshop in navi mumbai. I havent been there. got the address from the dealer section. you could call him n check if he can help u fix ur gun.

Technika
W 83 (B) Rabale Ttc Indl Area,
Plot No 13 Thane Belapur Road,
Rabale
Navimumbai 400701

Tel (Shop) - +91-22-27603866
Contact: Hitendra Doshi

regards
Parag

Hi Ketan,

Check if the barrel of your Jimy is slightly bent. Open the barrel and see if the muzzle end is perfectly round in shape (like a full moon). Even if there is little bend the pellet won't travel out of the barrel. This happened to a friend of mine with a National air rifle.

Regards
Ebenezer

Even if there is little bend the pellet won't travel out of the barrel.

A slight bend in the barrel wont stop the pellet from exiting the barrel.

The reasons, I can think of at the moment, for a pellet not exiting the barrel could be:

1) Use of an oversize for calibre pellet. eg G. Smiths are very tight fits in some Indian airguns.

2) The breech seal has completely failed thereby letting the air escape.

3) The piston washer is completely knackered thereby making the gun extremely underpowered.

It could be a combination of one, two or all three of the above reasons. I am assuming that the manufacturers have atleast bored the barrel for the right calibre.

A weak spring, or damaged piston, air leaks often produce such results.

Check for these areas. The make of that gun imples the finish will be comparatively much crude to IHP.

I guess it would be best to discard that old rifle if you already have an IHP.

Hi all,

Thanks for the reply special thanks to Archer & Guruji.Archer i had called up in technika but nobody is picking up the phone there .
Archer where r u from if we r near by can we meet up once .

Thank you
Ketan.

Mandal Aabhari Aahe.

Hi Shahid Bhai,

I cannot Discard that Air-Rifle coz it was gifted to me by my Grand Father
I have lot of good memories with it i cannot forget the day when he gave me the surprize he taught me how to break & fire that was the only gun on which i learnt lot of shooting things & techniques.

Even if the gun doesnt work will be fine for me i will keep it in my collection
But i can not see her lying on a wall as if there is nobody for her.

My father is not intrested in guns thats why he told me to take it back along with me to my new home.

Thanks & Regards
Ketan.

hi Ketan,

jst cant stop myself replying u..
in such case i would have taken a leave atleast for a day at any COST..

nyways.. best of luck.. hope u find all necessary parts to make it work again..


Best Regards
Rahul

Look for what Mack The Knife said that should fix the problem.
You can install the spring and washer yourself.
We can take you thru the process if you wish.
Provided of course that you post pics of the process as it proceeds
what say? you game?