Indians For Guns

It arrived this afternoon after a prolonged delay as the dealer had sent it back to BRK to have a small flaw removed. Whoever worked on this knife needs to get his eyes checked because it's still present. It's a small cosmetic flaw and nothing I cannot rectify but annoying none the less.

As for the knife, the first thing I noticed was the thickness of the handle. I did not like it at first but am already used to it. The handle is noticeably heavy and has a very planted feeling in the hand.

The finger grooves provide a secure grip without being annoying or uncomfortable. However, it remains to be seen whether this continues to be the case when the knife is actually used.

I noticed that a pinched grip is not comfortable due to the thickness of the handle. Perhaps it's the liners that add to this.

There is no need for jimping as the thumb comfortably resides in the valley between the blade and handle. However, extending / resting the forefinger above the spine creates too large a gap between finger and knife and this will prove to be a problem for certain tasks.

I have also noticed that when held in a regular or thumb on spine grip, the tip feels out of line. I like the shallow belly though.

This is a unique knife and requires more time spent working with it before I form any solid opinions about it.

For those who were undecided whether to get a Fox River or Canadian Special, I would advice buying the Fox River, even though I only have the mini variant of the same.

Herewith the obligatory pics.

Just noticed a small design flaw on the sheath. See the third pic from the top and you will see the back of the sheath covers the lanyard hole.

Thanks for posting that review.
That is one really good looking knife. It is the A2 version?

Dammit Mack The Knife, I had decided on a BRKT Gunny and now you have made me have second thoughts.

Yes, this is in A2 tool steel.

Having understood your requirements I would recommend either a Mini Fox River, Fox River or Custom Drop Point Hunter. If, however, you still decide on a Gunny, get the rampless version or have your dealer send it to BRK to have the ramp removed at the factory. This is a free service provided by BRK but you will have to reimburse the dealer the cost of postage.

If any of the BRK dealers, with a brick and mortar shop, happen to be in your neck of the woods, it would be adviseable to get a feel of the MFR, FR, Gunny, CS or CDPH in person. http://www.barkriverknifetool.com/Dealers.htm

Let us know what you finally end up with.

P.S.: Don't forget to get yourself a strop and stropping compound. The black compound is essential. The green and white are more for polishing the edge.

Surprise! Surprise!

I thought you would be getting it after a few days. Looks good, in fact better than what you see in those studio pics!

Let us know what you think of it after putting it to use for a few days when you get the opportunity. Thanks!

On a buying spree these days. Whats up?

Rajat, did a bit of wood and cardboard cutting and it doesn't feel odd in the hand at all. Need to do some finer tasks with it but basically it felt just fine in the hand.
Ordered a Fox River. Should be with the dealer next week and in my hands by mid-September or earlier. May or may not sell the CS after I have played with the FR.

On a buying spree these days. Whats up?

Out with the old, barring a very few, and in with the new. Whilst it may look like I am increasing the collection, I am actually down-sizing and only intend keeping those that meet my needs.

The plan is to have one small, one medium and one large knife from the ESEE and BRK line-up + a decent folder and call it good.

Mack The Knife Bana wrote:

On a buying spree these days. Whats up?

call it good.

Knowing you, No chance.

Nice blades those BRK.

Busted!

Well....there is that Aurora that's been calling out to me since it was released and then those Goloks appear to be mighty interesting and....

Okay, I'll admit to the truth. I dipped into your safe!