Indians For Guns

bhuvneshver1234 wrote: ↑

Wed Nov 11, 2020 2:35 pm

Can anyone of members experience with old single shot .22 rifle.i saw many rifle on internet the old single shot rifle had no mount to tap scope on it but many gun dealer say it's not a problem to fix a riflescope on gun just simply by drilling and tapscrew and rail plate on it.please guys share your experiences if you had this kind of rifle.and plz write your opinion good or bad.and it is worth than a iof .22 rifle.

bhuvneshver1234 wrote: ↑

Wed Nov 11, 2020 2:35 pm

Can anyone of members experience with old single shot .22 rifle.i saw many rifle on internet the old single shot rifle had no mount to tap scope on it but many gun dealer say it's not a problem to fix a riflescope on gun just simply by drilling and tapscrew and rail plate on it.please guys share your experiences if you had this kind of rifle.and plz write your opinion good or bad.and it is worth than a iof .22 rifle.

Go for brand new iof .22 rather than 100 years old single shot imported rifle.

Vineet wrote: ↑

Wed Nov 11, 2020 5:28 pm

Go for brand new iof .22 rather than 100 years old single shot imported rifle.

Bishop wrote: ↑

Wed Nov 11, 2020 4:06 pm

bhuvneshver1234 wrote: ↑

Wed Nov 11, 2020 2:35 pm

Can anyone of members experience with old single shot .22 rifle.i saw many rifle on internet the old single shot rifle had no mount to tap scope on it but many gun dealer say it's not a problem to fix a riflescope on gun just simply by drilling and tapscrew and rail plate on it.please guys share your experiences if you had this kind of rifle.and plz write your opinion good or bad.and it is worth than a iof .22 rifle.

Yes, it's possible to drill and tap the reciever to screw in a scope rail.A competent Gunsmith will be able to do it.You can tell whether it's worth it or not only after trying it out.If you can grab one for not more than 35k , it's well worth than IOF .22 LR rifle which will require lots of work to turn it into a shooter.

timmy wrote: ↑

Thu Nov 12, 2020 1:05 am

Make sure, if you have someone drilling and tapping holes in a gun (including for mounting a rail), they know what they are doing. For instance, you want someone with the necessary skill and equipment who can mount the thing straight. You also want someone who will put things together without needing to do surgery on the bolt handle

I have personally seen examples of this: a really nice Winchester Model 75 .22 where the base of the bolt handle had to be ground down to clear the rail. When I got it, I fixed it and it has a new handle, but the ugly holes are still in the top of the receiver. I gave it to one of my boys, who still has it. (Note: a Model 75 is a "man's gun" in that, while a .22, it is sized and styled like a real hunting rifle, with a very nice walnut checkered stock. It's a real shame that such a nice gun was butchered like this!(

My uncle gave my brother and I his guns, which included a very nice looking 1903 Springfield stocked in a fine piece of Bishop walnut wood. The side mount scope was put on using a really nice Mikron detachable side mount -- but the holes drilled in the receiver are not straight, so on close inspection, the scope sits cross-ways on top of the action. Furthermore, the magazine was inletted into the stock too deeply, which the "gunsmith" fixed by eliminating the pillar tubes, so the magazine bears against the action when the stock screws are tightened. No matter what is done, that gun will never shoot right because of this! To put the scars of the rear sight retaining pin on the bottom of the barrel, our genius threaded the barrel into the receiver a little more deeply (this is one way I know it was a gunsmith -- he had to have a lathe to do this) and the extractor notch in the barrel cone didn't line up, so he cut pie shaped section from the cone and now about 1/4 of it is missing, as he didn't turn the barrel in far enough to use the original extractor slot fully. Finally, he didn't weld the handle back on to the brightly polished bolt correctly, and the handle broke off.

All of the above would tell me that you should take the advice given above. I've seen plenty of guns in the shops that look like cheese graters from the holes of these people modifying them. Unless you have someone who can do work who REALLY knows what he's doing, then just get a gun that's grooved for a scope from the beginning.

I have my Marlin 39A .22 from when I was a kid -- these old ones (it's as old as I am) are really nice, and it is VERY accurate. I would love to put a scope on it to aid my old, tired eyes, but I won't have anyone drilling holes in the thing. I made other arrangements with a different gun, and I'll shoot the Marlin every now and then for fun. I fully understand the allure of old guns, as most of mine are old. I love old guns, but there's a point where asking them to do something that they aren't made for is going too far.

But, in the end, it's your choice -- YOU have to be the one who is satisfied and has to live with the result.

Bishop wrote: ↑

Wed Nov 11, 2020 4:06 pm

bhuvneshver1234 wrote: ↑

Wed Nov 11, 2020 2:35 pm

Can anyone of members experience with old single shot .22 rifle.i saw many rifle on internet the old single shot rifle had no mount to tap scope on it but many gun dealer say it's not a problem to fix a riflescope on gun just simply by drilling and tapscrew and rail plate on it.please guys share your experiences if you had this kind of rifle.and plz write your opinion good or bad.and it is worth than a iof .22 rifle.

Yes, it's possible to drill and tap the reciever to screw in a scope rail.A competent Gunsmith will be able to do it.You can tell whether it's worth it or not only after trying it out.If you can grab one for not more than 35k , it's well worth than IOF .22 LR rifle which will require lots of work to turn it into a shooter.